| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
1 |
Perforated strip | 12 ½" | tinplated/1923-35 | |
1a |
Perforated strip | 9 ½" | tinplated/1923-35 | |
1b |
Perforated strip | 7 ½" | tinplated/1923-35 | |
2 |
Perforated strip | 5 ½" | tinplated/1923-35 | |
e2 |
Motor with reverse | 6V DC - green/10x5h.sideplates/7h.mounting flanges/1926-30 | ||
2a |
Perforated strip | 4 ½" | tinplated/1923-35 | |
e2a |
Motor separate | (use w/gm-173) Low voltage - nickelplated side plates/Erector P58 without mounting flanges/1930-34 | ||
e2b |
Motor w/gearbox side plates | E2A with 173l and 173r/1930-34 - low voltage | ||
e2d |
Motor w/gearbox side plates | Erector A52 with 191l and 191r/1935 - 110 volt | ||
3 |
Perforated strip | 3 ½" | tinplated/1923-35 | |
e3 |
Motor 110 volt | Black casing/Erector P56G part of P66/drive shaft out both sides/1930-35 | ||
4 |
Perforated strip | 3" | tinplated/1923-35 | |
5 |
Perforated strip | 2 ½" | tinplated/1923-35 | |
6 |
Perforated strip | 2" | tinplated/1923-35 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
6a |
Perforated strip | 1 ½" | tinplated/1923-35 | |
7 |
Angle girder | 24 ½" | tinplated/1923-35 | |
7a |
Angle girder | 18 ½" | tinplated/1923-35/Erector MB | |
8 |
Angle girder | 12 ½" | tinplated/1923-35 | |
8a |
Angle girder | 9 ½" | tinplated/1923-35 | |
8b |
Angle girder | 7 ½" | tinplated/1923-35 | |
9 |
Angle girder | 5 ½" | tinplated/1923-35 | |
9a |
Angle girder | 4 ½" | tinplated/1923-35 | |
9b |
Angle girder | 3 ½" | tinplated/1923-35 | |
9c |
Angle girder | 3" | tinplated/1923-35 | |
9d |
Angle girder | 2 ½" | tinplated/1923-35 | |
9e |
Angle girder | 2" | tinplated/1923-35 | |
9f |
Angle girder | 1 ½" | tinplated/1923-35 | |
10 |
Fishplate | tinplated/1923-35 | ||
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
11 |
Double bracket | ½"x ½"x½" | nickelplated/Erector M/1930-35 | |
11 |
Double bracket | ½"x ½"x½" | tinplated/1923-30 | |
12 |
Angle bracket | ½"x0.4" | tinplated/1923-35 | |
12a |
Angle bracket | 1"x1" | tinplated/1923-35 | |
12b |
Angle bracket | 1"x½" | tinplated/1924-35 | |
13 |
Axle rod | 11 ½"l x 160"d. | tinplated/guillotined ends/1923-30 | |
13 |
Axle rod | 12"l x 157"d. | tinplated/guillotined ends/1930-35/Erector P57F | |
13a |
Axle rod | 8"l x 160"d. | tinplated/guillotined ends/1923-30 | |
13a |
Axle rod | 8"l x 157"d. | tinplated/guillotined ends/1930-35/Erector P57E | |
13b |
Axle rod | 19.8"l x 157"d. | tinplated/guillotined ends/1930-35/Erector AX | |
13c |
Axle rod | 10"l x 157"d. | tinplated/guillotined ends/1930-35/Erector DA | |
14 |
Axle rod | 6"l x 160"d. | tinplated/guillotined ends/1923-24 | |
14 |
Axle rod | 6 ½"l x 160"d. | tinplated/guillotined ends/1925-30 | |
14 |
Axle rod | 7"l x 157"d. | tinplated/guillotined ends/1930-35/Erector CZ | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
14a |
Axle rod | 6"l x 157"d. | tinplated/guillotined ends/1930-35/Erector P57D | |
15 |
Axle rod | 5"l x 160"d. | tinplated/guillotined ends/1923-30 | |
15 |
Axle rod | 5"l x 157"d. | tinplated/guillotined ends/1930-35/Erector CY | |
15a |
Axle rod | 4 ½"l x 160"d. | tinplated/guillotined ends/1923-30 | |
16 |
Axle rod | 3 ½"l x 160"d. | tinplated/guillotined ends/1923-30 | |
16 |
Axle rod | 4"l x 157"d. | tinplated/guillotined ends/1930-35/Erector AT | |
16a |
Axle rod | 3"l x 157"d. | tinplated/guillotined ends/1930-35/Erector AS | |
16a |
Axle rod | 2 ½"l x 160"d. | tinplated/guillotined ends/1923-30 | |
16b |
Axle rod | 3"l x 160"d. | tinplated/guillotined ends/1924-30 | |
17 |
Axle rod | 2"l x 160"d. | tinplated/guillotined ends/1923-30 | |
17 |
Axle rod | 2"l x 157"d. | tinplated/guillotined ends/1930-35/Erector P57A | |
18a |
Axle rod | 1 ½"l x 160"d. | tinplated/guillotined ends/1923-30 | |
18b |
Axle rod | 1"l x 160"d. | tinplated/guillotined ends/1923-30 | |
18b |
Axle rod | 1"l x 157"d. | tinplated/guillotined ends/1930-35/Erector CX | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
19 |
Crank handle/long | 5"l x 160"d. | tinplated/guillotined ends/1923-30 | |
19a |
Wheel/spoked with boss | 3" d. | glossy black/single tapped boss/1923-30 | |
19b |
Pulley/solid design | 3" d. | burgundy red/single tapped boss/1926-31 | |
19b |
Pulley/spoked design | 3" d. | nickelplated or painted black/single tapped boss/1923-25 | |
19b |
Pulley/solid design | 3" d. | light green/Erector boss single tapped 6-32/1931-35 | |
19c |
Pulley | 6" d. | red/1926-1935 | |
19s |
Crank handle | 3 ½"l x 157"d. | tinplated/Erector P24/1930-35 | |
19s |
Crank handle | 3 ½"l x 160"d. | tinplated/guillotined ends/1928-30 | |
20 |
Wheel/flanged | 1.13" d. | brass/4 holes/singletapped boss/1923-35 | |
20a |
Pulley/4-spoke design | 2" d. | burgundy red/singletapped boss/1926-30 | |
20a |
Pulley/4-spoke design | 2" d. | glossy black(?)/singletapped boss/1923-26 | |
20b |
Wheel/flanged | ¾" d. | brass/singletapped boss/1928-35 | |
21 |
Pulley | 1 ½" d. | brass/8 holes/singletapped boss/1923-30 - 1.13" d.;brassplated/Erector P7/boss tapped 6-32/1930-35 - 1 | |
22 |
Pulley with boss | 0.88" | brassplated/Erector P7A/boss tapped 6-32/1930-35 - 1" d.;brassplated/unique design/Erector boss tappe | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
22a |
Pulley no boss | 1" | brass/3 holes/1923-30 - 0.88" d.(?);nickelplated/Erector AM/1930-35 | |
23 |
Pulley no boss | ½" | brass/1923-35 | |
23a |
Pulley with boss | ½" | brass/singletapped boss/1923-30 | |
24 |
Bush wheel 8 holes | 1.26" d. | brassplated/Erector BT/boss single tapped 6-32/1930-35 - 1.41" d.;brass/single tapped boss/1923-30 | |
24a |
Bush wheel 8 holes | 1.30" d. | nickel or brass plated/Erector BAX for.25"axle/boss tapped 8-32/1930-35 | |
25 |
Pinion | 25T x ¼" | brass/.25"face/single tapped boss/1923-30 | |
25a |
Pinion | 25T x ¾" | brass/.50"face/single tapped boss/1928-30 | |
25c |
Pinion | 18T | brass/Erector P49/boss single tapped 6-32/1930-35 | |
26 |
Pinion | 19T x ½" | brass/.25"face/single tapped boss/1923-30 | |
26a |
Pinion | 19T x ½" | brass/.50"face/single tapped boss/1928-30 | |
26c |
Pinion | 12T x ½" | brass/Erector P13/boss single tapped 6-32/1930-35 | |
27 |
Gear (no boss) | 72T 3" | brassplated/.31"dia.center hole/Erector P50/1930-35 - 1 ¼" d. 50t;brass/no holes/single tapped boss/1 | |
27a |
Gear wheel | 57T 1 ½" | brass/8 holes/single tapped boss/1923-30 | |
27b |
Gear wheel | 133T 3 ½" | unknown finish/1925-30 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
27c |
Gear wheel | 36T 1 ½" | brassplated/Erector CJ/boss single tapped 6-32/1930-35 | |
28 |
Contrate wheel | 50T 1 ½" | brass/8 holes/single tapped boss/1923-30 | |
28c |
Gear/crown | 32T | brassplated/8 holes/Erector P12/boss single tapped 6-32/1930-35 | |
29 |
Contrate wheel | 25T x ¼" | brass/single tapped boss/1923-30 | |
30 |
Bevel gear | 26T 0.88" | brass/single tapped boss/1923-35 | |
30a |
Bevel gear | 16T ½" | brass/used only with 30c/single tapped boss/1928-35 | |
30c |
Bevel gear | 48T 1 ½" | brass/used only with 30a/single tapped boss/1928-35 | |
30d |
Gear/mitre | 10t | grayish white metal/Erector P48 early style/boss single tap 6-32/1930-35 | |
31 |
Gear wheel | 38T 1" | brass/1923-30 | |
32 |
Worm gear | ½" | brass/0.76"wide/flat end/single tapped boss/1923-30 | |
32c |
Worm gear | brassplated/for 25c-26c-27c/Erector P14/boss single tapped 6-32/1930-35 | ||
33. |
Pawl (early sheetmetal type) | chemically blackened/1923 only | ||
33 |
Pawl with boss | nickelplated/hammerhead style/singletapped boss/1924-25/see 147a | ||
33a |
Bolt/pivot with nuts | nickelplated/slotted head/1925 only/see 147b | ||
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
34 |
Wrench | 3.3" l. o/a | nickelplated/flat double ended/Erector CB/1930-35 - Spanner;;nickelplated/cranked/1923-30 | |
34b |
Spanner/box | nickelplated/1924-30 | ||
35 |
Spring clip | chemically blackened/narrow sides/1923-30 | ||
36 |
Screwdriver/wire handle | nickelplated/rectangular handle/Erector P33/1930-35 - Rod type;4 ½" l. o/a;nickelplated/rounded handl | ||
36a |
Screwdriver/wooden handle | 7 ¾" l. o/a | Reddish brown wooden handle/Erector B2/1930-35 - Extra long;;nickelplated(?)/1923-30 | |
37 |
Bolt with square nut | 0.22" l. | brassplated/slotted cheesehead/1923-30 | |
37a |
Nut/square | ¼" | nickelplated/Erector N21/about .80"thick/U.S.8-32 threads/1930-35 - ¼" square;brassplated/.064"-.070" | |
37b |
Screw | 0 ¼" l. | nickelplated/Erector S51/U.S.8-32 threads/1930-35 - Bolt;0.22" l.;brassplated/slotted cheesehead/BSW | |
38 |
Washer | 0.38" d. | nickelplated/approx..040"-.050"thick/slightly cupped/Erector BL/1923-35 | |
38a |
Ship gasket washer | 0.63" d. | fibre gasket material about .07"thick/1930-35 | |
40 |
Cord/hank | 40"(?) | burgundy red color/1923-32? - Unknown;white or off-white color/Erector P34/1930-35 | |
41. |
Propeller blade (early) | tinplated/early style/1923-26 - burgundy red/early style/1926-27 - Late burgundy red/later style/1928- | ||
43 |
Tension spring | 0.56"l.x0.38"d. | nickelplated/Erector AE/1930-35 - 2" l.;chemically blackened or nickelplated/1923-30 | |
44 |
Bracket/cranked bent | tinplated/three holes/1923-35 | ||
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
45 |
Double bracket bent strip | tinplated/5 hole strip formed/1923-30 - nickelplated/Erector P20 five hole strip formed/1930-35 | ||
46 |
Double angle bracket | 2 ½" x 1" | tinplated/1923-35 | |
47 |
Double angle bracket | 2 ½" x 1 ½" | tinplated/1923-35 | |
47a |
Double angle bracket | 3" x 1 ½" | tinplated/1923-35 | |
48 |
Double angle bracket | 1 ½" x ½" | tinplated/1923-35 | |
48a |
Double angle bracket | 2 ½" x ½" | tinplated/1923-35 | |
48b |
Double angle bracket | 3 ½" x ½" | tinplated/1923-35 | |
48c |
Double angle bracket | 4 ½" x ½" | tinplated/1923-35 | |
48d |
Double angle bracket | 5 ½" x ½" | tinplated/1924-30 | |
50 |
Eye piece without boss | brass/1923-27 | ||
50a |
Eye piece with boss | brass/manual shows four radial bores in boss/1928-35 | ||
52 |
Flanged plate long sides only | 5 ½" x 2 ½" | burgundy red/no slots/1926-30 - nickelplated/no slots/1923-26 - All four sides;5 ½" x 2 ½";burgundy re | |
52a |
Flat plate | 5 ½" x 3 ½" | nickelplated/1923-26 - burgundy red/1926-35 | |
52b |
Flanged plate all four sides | 5 ½" x 16 ½" | red-orange/no.110-150 sets/1930-35 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
53 |
Flanged plate short sides only | 3 ½" x 2 ½" | nickelplated/1923-26 - burgundy red/1926-30 - red-orange/1930-35 | |
53a |
Flat plate | 4 ½" x 2 ½" | nickelplated/end holes slotted/1923-26 - burgundy red/end holes slotted/1926-35 | |
54 |
Flanged sector plate | 4" l. | nickelplated/one row of center holes/1923-26 - burgundy red 1926-30 - burgundy red/three rows of cente | |
55 |
Slotted strip | 5 ½" l. | tinplated/1924-35 | |
55a |
Slotted strip | 2" l. | tinplated/1924-35 | |
56 |
Manual no. 1 | 1923 | ||
56a |
Manual no. 2 | 1923 - for No. 0-3 outfits;;1924-27 - for No. 00-3x outfits;;1928 - for No. 0-40 outfits;;1929-30/same | ||
56b |
Manual for no. 4-6 outfits | 1924-27 - for No. 4x-6x outfits;;1928 - for No. 50-70 outfits;;1929-30/same as 1928 but different outf | ||
56c |
Manual for no. 00 outfit | 1926-28 | ||
56d |
Manual/Standard Mechanisms | 1928-30 | ||
57 |
Hook/wire type | 1.1" l. | nickelplated/90 mil gauge/1923-30 - 0.94" l.;nickel or tinplated/Erector AF/1930-35 | |
57a |
Hook/scientific | unknown finish/1924-30 | ||
57b |
Hook/loaded | unknown finish/1924-30 | ||
57c |
Hook/large | 2 ¼" l. o/a | nickelplated/.156"dia. rod/Erector AG/1930-35 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
p57m |
Motor | 1930- | ||
58 |
Cord/spring | 40" | unknown finish/1923-32 | |
59 |
Collar with set screw | .375"d x 250"w. | brass/single tapped BSW/1923-30 - single tapped 6-32/1930-35 | |
59a |
Collar/formed | nickelplated/u-shaped/Erector P37/tapped 6-32/1930-35 | ||
59b |
Collar/formed twin | nickelplated/long sides with slotted holes/single 6-32 tap/1930-32? | ||
60 |
Double angle bracket | 2 ½" x ½" | tinplated/1923 only/became 48a after 1923 | |
60a |
Double angle bracket | 1 ½" x ½" | tinplated/1923 only/became 48 after 1923 | |
60b |
Double angle bracket | 3 ½" x ½" | tinplated/1923 only/became 48b after 1923 | |
60c |
Double angle bracket | 5 ½" x ½" | tinplated/1923 only/became 48d after 1923 | |
60d |
Double angle bracket | 4 ½" x ½" | tinplated/1923 only/became 48c after 1923 | |
p60d |
Transformer 110 volt | 1930- | ||
61 |
Windmill sail | tinplated/7 holes/short shank/1923-26#burgundy red 1926-30 | ||
62 |
Crank | nickelplated or black/rounded shoulder/single tapped boss/1923-27 - straight shoulder 1928-30 - Erecto | ||
62a |
Threaded crank | nickelplated or black/rounded shoulder/single tapped boss/1923-27 - straight shoulder/single tapped b | ||
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
62b |
Double arm crank | nickelplated/single tapped boss/1928-30 | ||
63. |
Coupling (early) | 0.82" w. | brass/9 radial holes/1923-27(?) | |
63 |
Coupling | 0.82" w. | brass/12 radial holes/1928(?)-32 | |
63a |
Octagonal coupling | brass/1924-30 | ||
63b |
Strip coupling | 0.94" w. | brass/1923-30 - 0.63"l.x0.31"d.;brass/Erector CQ/two 6-32 taps/1930-35 | |
63c |
Threaded coupling | brass/1924-30 | ||
64 |
Threaded boss | brass/1924-30 | ||
65 |
Center fork | tinplated/one end guillotined/1923-30 | ||
66 |
Weight 50 grams | unknown finish/1923-30 | ||
p66 |
Power hoist/disc clutch | Erector P66 "2-drum hoist" takes P56G motor/1930-35 | ||
67 |
Weight 25 grams | unknown finish/1923-30 | ||
68 |
Wood screw | ½" | unknown finish/1924-30 - 0.625";unknown finish/1930-35? | |
69 |
Set screw | brassplated/1923-30 | ||
69a |
Grub screw | .156" l. | chemically blackened/1923-30 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
69b |
Grub screw | .219" l. | chemically blackened/1924-30 | |
70 |
Flat plate | 5 ½" x 2 ½" | burgundy red/1926-35 | |
70 |
Flat plate | 5 ½" x 2 ½" | nickelplated/1923-26 | |
72 |
Flat plate | 2 ½" x 2 ½" | nickelplated/1923-26 - burgundy red/1926-35 | |
76 |
Triangular plate | 2 ½" | nickelplated/1923-26 - burgundy red/1926-35 | |
77 |
Triangular plate | 1" | nickelplated/1923-26 - burgundy red/1926-35 | |
78 |
Screwed rod | 11 ½" l. | brassplated/1924-30 | |
79 |
Screwed rod | 8" l. | brassplated/1923-30 | |
79a |
Screwed rod | 6" l. | brassplated/1923-30 | |
80 |
Screwed rod | 5" l. | brassplated/1923-30 | |
80a |
Screwed rod | 3 ½" l. | brassplated/1923-30 | |
80b |
Screwed rod | 4 ½" l. | brassplated/1923-30 | |
81 |
Screwed rod | 2" l. | brassplated/1923-30 | |
82 |
Screwed rod | 1" l. | brassplated/1923-30 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
89 |
Curved strip | 5 ½" l. | tinplated/1923-30 - l.;green/1930-35 | |
89a |
Curved strip stepped | 3" l. | green/1928-35 | |
90 |
Curved strip | 2 ½" l. | green/1926-35 - tinplated/1923-26 | |
90a |
Curved strip stepped | 2 ½" l. | green/1926-35 | |
94 |
Sprocket chain | 40" | tinplated/1923-30 - nickelplated/for 25c-26c-27-27c/Erector P52/1930-35 | |
94a |
Sprocket chain | 10 feet | nickelplated/for 25c-26c-27-27c/Erector P52A/1930-35 | |
95 |
Sprocket wheel | 2" d. 36t | tinplated/8 holes/1923-30 | |
95a |
Sprocket wheel | 1 ½" d. 28t | tinplated/8 holes/1924-30 | |
95b |
Sprocket wheel | 3" d. 56t | tinplated/1924-30 | |
96 |
Sprocket wheel | 1" d. 18t | tinplated/1923-30 | |
96a |
Sprocket wheel | ¾" d. 14t | tinplated/1924-30 | |
97 |
Braced girder | 3 ½" | tinplated/open ends/rounded corners/1923-26 - green/open ends/rounded corners/1926-30 | |
97a |
Braced girder | 3" | green/open ends/rounded corners/1926-30 | |
98 |
Braced girder | 2 ½" | tinplated/open ends/rounded corners/1923-26 - green/open ends/rounded corners/1926-30 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
99 |
Braced girder | 12 ½" | green/open ends/rounded corners/1926-30 - green/special Gilbert Meccano style/1930-35 - tinplated/open | |
99a |
Braced girder | 9 ½" | tinplated/open ends/rounded corners/1923-26 - green/open ends/rounded corners/1926-30 | |
99b |
Braced girder | 7 ½" | green/open ends/rounded corners/1926-30 | |
100 |
Braced girder | 5 ½" | green/open ends/rounded corners/1926-30 - green/special Gilbert Meccano style/1930-35 - tinplated/open | |
100a |
Braced girder | 4 ½" | green/open ends/rounded corners/1926-30 - 3½";green/special Gilbert Meccano style/1930-35 | |
100b |
Girder/curved beam | 6" l. | red-orange/flanged one side only/No.150 set only/Erector DV/1930-35 | |
101 |
Loom heald/bundle 24 | unknown finish/1923-30 | ||
102 |
Bracket/single bent strip | 1.40"x0.45" | tinplated/1923-35 | |
103 |
Flat girder | 5 ½" | tinplated/rounded ends/1923-35 | |
103a |
Flat girder | 9 ½" | tinplated/rounded ends/1923-35 | |
103b |
Flat girder | 12 ½" | tinplated/rounded ends/1923-35 | |
103c |
Flat girder | 4 ½" | tinplated/rounded ends/1923-35 | |
103d |
Flat girder | 3 ½" | tinplated/rounded ends/1923-35 | |
103e |
Flat girder | 3" | tinplated/rounded ends/1923-35 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
103f |
Flat girder | 2 ½" | tinplated/rounded ends/1923-35 | |
103g |
Flat girder | 2" | tinplated/rounded ends/1923-35 | |
103h |
Flat girder | 1 ½" | tinplated/rounded ends/1923-35 | |
103k |
Flat girder | 7 ½" | tinplated/rounded ends/1923-35 | |
104 |
Loom shuttle | nickelplated/1923-30 | ||
105 |
Loom reed hook | unknown finish/1923-30 | ||
106 |
Loom wooden roller | 1923-30 | ||
106a |
Loom sand roller | 1923-30 | ||
107 |
Table for designing machine | green/with bush wheel installed/1923-30 | ||
108 |
Bracket/architrave | 2 ½" x 2" | burgundy red/1926-35 | |
108 |
Bracket/architrave | 2 ½" x 2" | tinplated/1923-26 | |
109 |
Face plate with boss | 2 ½" d. | green/Erector boss singletapped 6-32/1930-35 - tinplated/single tapped boss/1923-26 - burgundy red/sin | |
110 |
Rack strip | 3 ½" | unknown finish/1923-30 - 4 ½";nickelplated/Erector FJ/1930-32 | |
111 |
Screw | 0.88" | nickelplated/Erector S62/U.S.8-32 thread/1930-35 - Bolt;¾";brassplated/slotted cheesehead/1923-30 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
111a |
Screw | ½" | nickelplated/Erector S52/U.S.8-32 thread/1930-35 - Bolt;½";brassplated/slotted cheesehead/1924-30 | |
111b |
Bolt cheesehead | 0.22" | brassplated/slotted cheesehead/1924-25 | |
111c |
Bolt | 0.38" | brassplated/slotted cheesehead/1926-30 - Screw;1.38";nickelplated/Erector S57/U.S.8-32 thread/1930-35 | |
111d |
Screw | 1 ¾" | nickelplated/Erector FA/U.S.8-32 thread/1930-35 | |
112 |
Double angle bracket | 2 ½" x 1 ½" | tinplated/1923 only/became 47 after 1923 | |
112a |
Double angle bracket | 3" x 1 ½" | tinplated/1923 only/became 47a after 1923 | |
113 |
Girder frame | 5 ½" l. | unknown finish/1923-35 | |
114 |
Hinge | nickelplated/1923-30 - Hinge loop;;nickelplated/Erector FD/1930-35 | ||
115 |
Pin/threaded | 0.45"shank | nickelplated/small round shoulder/1923-30 | |
116 |
Fork piece/large with boss | tin or nickel plated/single tapped boss/1924-35 | ||
116a |
Fork piece/small with boss | nickelplated/single tapped boss/1928-30 - Erector boss singletapped 6-32/1930-35 | ||
117 |
Ball/steel | .375" d. | unknown finish/1924-30 | |
118 |
Hub disc | 5 ½" d. | burgundy red/1924-35 | |
119 |
Channel segment | 11 ½" d. | unknown finish/8 to a circle/1926-35? | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
120 |
Train buffer | brass/1923-27 | ||
120a |
Train spring buffer | brass/1924-27 | ||
120b |
Compression spring | unknown finish/1928-30 | ||
121 |
Train coupling | brass/1923-27 | ||
122 |
Sack/miniature loaded | 1923-30 | ||
123 |
Cone pulley | brass/.31"dia. boss tapped 6-32/Erector FM/1930-32 | ||
123 |
Cone pulley | brass/singletapped boss/1923-30 | ||
124 |
Reverse-angle bracket | 1" | tinplated/1923-35 | |
125 |
Reverse-angle bracket | ½" | tinplated/1923-35 | |
126 |
Trunnion flanged | tinplated/1923-26 - green/1926-35 | ||
126a |
Flat trunnion | green/1926-35 - tinplated/1923-26 | ||
127 |
Crank/bell without boss | unknown finish/1923-35 | ||
128 |
Crank/bell with boss | unknown finish/1923-35 | ||
129 |
Gear/quarter | 3 ½" d. | black/no boss/Erector FX/1930-35 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
129 |
Rack segment 90 degrees | 3" d. | nickelplated/no boss/1923-30 | |
130 |
Eccentric/triple throw | tinplated/single tapped bosses/1923-35 | ||
131 |
Bucket/dredger | unknown finish/1924-30 - Bucket/chain;2" w.;red/Erector BV/1930-35 | ||
132 |
Flywheel | 2 ¾" d. | black(?)/1924-30 | |
133 |
Corner bracket | 1 ½" x 1 ½" | tinplated/1923-26 - burgundy red/1926-35 | |
134 |
Crank shaft/1.0"stroke | .160" d. | nickel plated/1923-30 | |
135 |
Theodolite protractor | 1923-30 - Dial/180 degrees;;1930-35 | ||
135a |
Dial/300 degrees | 1930-35 | ||
136 |
Handrail support | brass/single tapped boss/1924-30 - ½"l.x0.31"d.;brass/Erector DT/1930-35 | ||
137 |
Wheel flange | unknown finish/1924-26 - burgundy red/1926-35? | ||
138 |
Ship's funnel | red-orange/black stripe on top/no steam pipe/1930-35? | ||
138a |
Ship's funnel/Cunard type | burgundy red/black stripe on top/with steam pipe/1928-30 - red-orange/black stripe on top/with steam | ||
139 |
Flanged bracket RH | tinplated/1924-35 | ||
139a |
Flanged bracket LH | tinplated/1924-35 | ||
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
140 |
Coupling/universal | nickelplated/singletapped bosses/1924-30 | ||
141 |
Wire Lines | for suspending clock weights/unknown finish/1928-30 | ||
142 |
Tyre/rubber ring | white(?)/flexible ring for 3" pulley/1925-27 | ||
142a |
Tyre/Dunlop | 2" | black/marked"MECCANO DUNLOP BALLOON"/1928-30 | |
142b |
Tyre/Dunlop for 19b | 3" | black/marked"MECCANO DUNLOP BALLOON"/1928-35 | |
143 |
Circular girder | 5 ½" d. | burgundy red/1926-35 | |
143 |
Circular girder | 5" d. | unknown finish/1925-26 | |
144 |
Dog clutch (2 pieces) | brass/1925-30 | ||
145 |
Circular strip | 7" d. | unknown finish/1925-26 - 7 ½" burgundy red/1926-35 | |
146 |
Circular plate | 6" d. | unknown finish/1925-26 - burgundy red/1926-35 | |
147 |
Pawl w/boss+pivot bolt&nuts | tinplated/modern style/1925-27 | ||
147a |
Pawl with boss | tinplated/modern style/singletapped brass boss/1926-30 | ||
147b |
Bolt/pivot with slotted head | 0.63" l. | nickel plated/with 2 square nuts/1926-30 | |
148 |
Wheel/ratchet | all brass with singletapped brass boss/1925-35 | ||
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
149 |
Collecting shoe for locomotive | 1926-27 only | ||
150 |
Crane grab | black/1928-35? | ||
151 |
Pulley block/single sheave | unknown color/1928-35? | ||
152 |
Pulley block/double sheave | unknown color/1928-30 | ||
153 |
Pulley block/triple sheave | unknown color/1928-30 | ||
154a |
Corner bracket angle RH | tinplated(?)/1928-35 | ||
154b |
Corner bracket angle LH | tinplated(?)/1928-35 | ||
155 |
Tyre/rubber ring | unknown color/1928-30 | ||
156 |
Pointer with boss | 2 ½" | unknown finish/singletapped boss/1928-35 | |
157 |
Fan | 2" dia. | unknown color/singletapped boss/1928-30 | |
158a |
Signal arm | red/Erector CA/no boss/1930-35 | ||
159 |
Saw blade/circular | nickelplated/with arbor/doubletapped brass boss/1928-30 | ||
160 |
Bracket/channel bearing | 1 ½"x1"x½" | burgundy red/1928-35 | |
162 |
Boiler with ends | 2.06"d.x4 ½"l. | green/1928-35 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
162a |
Boiler end | green/1928-35 | ||
162b. |
Radiator | black/unmarked Erector part/1930-35 | ||
162b |
Boiler body | green/1928-35 | ||
163 |
Sleeve piece | 0.69"d.x1.4"l. | green/1-2-1 hole pattern/1928-35 | |
164 |
Chimney adaptor | 0.63"d.x ½"h. | green/one hole/1928-35 | |
165 |
Swivel bearing | nickelplated with brass spider and single tapped boss/1928-35 | ||
166 |
End bearing | nickelplated with singletapped brass boss/1928-30 | ||
167 |
Roller bearing/geared | unknown color/1928-35 | ||
167a |
Roller race/Geared | unknown color/1928-35 | ||
167b |
Roller ring frame | unknown finish/1928-35 | ||
167c |
Roller race pinion | 16t | brass/1928-35 | |
168 |
Bearing assembly complete | 4" d. | dark green(?)/1928-35 | |
168a |
Bearing ball race/flanged | dark green(?)/1928-35 | ||
168b |
Bearing ball race/geared | dark green(?)/1928-35 | ||
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
168c |
Bearing ball casing with balls | unknown finish/1928-35 | ||
169 |
Digger bucket | black/Erector X spot-welded version with nickelplated catch/1930-32 - green 3-piece part with nickelp | ||
169a |
Bucket/tip with handle | nickelplated or black/Erector BP/1930-32 | ||
170 |
Single eccentric ½" throw | unknown finish/singletapped boss/1928-30 | ||
172 |
Ship hull | glossy black with MECCANO decal on bow/1930-35 | ||
172a |
Ship bow deck | yellow/1930-35 | ||
172b |
Ship mid deck | yellow/1930-35 | ||
172c |
Ship stern deck | yellow/1930-35 | ||
172d |
Ship cabin top | yellow/1930-35 | ||
172e |
Ship rudder | orange-red/1930-35 | ||
172f |
Ship keel | orange-red/1930-35 | ||
172g |
Ship ballast keel | orange-red/1930-35 | ||
172h |
Ship quill for rudder & prop | brass/1930-35 | ||
172i |
Ship quill nut | nickelplated/1930-35 | ||
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
172j |
Ship propeller | orange-red/boss single tapped 6-32/1930-35 | ||
172k |
Ship forward deck | yellow/1930-35 | ||
172l |
Ship pilot house top | nickel plated/1930-35 | ||
173l |
Motor side plate for E2A | glossy black/left hand/1930-35 | ||
173r |
Motor side plate for E2A | glossy black/right hand/1930-35 | ||
174 |
Ship loop rod | tin plated/1930-35 | ||
175 |
Ship elastic band | 5 ft. | 1930-35 | |
176 |
Bracket/foot block | black/.50"hole in center/Erector AW/1930-32 | ||
177 |
Strip | 12 ¼" | green/1933-35 | |
177 |
Reverse switch attachment | Erector BO/1930-32? | ||
178 |
Strip | 5 ¼" | green/1933-35 | |
179 |
Strip | 3 ¾" | green/1933-35 | |
181 |
Strip | 2 ¼" | green/1933-35 | |
182 |
Double angle bracket | 2 ¼" x ½"¾" | green/1933-35 | |
| Gilbert Meccano | ||||
|---|---|---|---|---|
| Part No | Description | Size | Notes | |
184 |
Angle bracket | ¾" x ½"¾" | nickelplated/1933-35 | |
187 |
Plate/base | 5 ¼"x2 ¼" | red/flanged long sides only/1933-35 | |
188 |
Plate/base | 2 ¼"x2 ¼" | red/flanged two sides only/1933-35 | |
189 |
Rivet snap | brassplated/1933-35 | ||
190 |
Rivet extractor | nickelplated/1933-35 | ||
191l |
Motor side plate LH | black/part of E2D/1935 | ||
191r |
Motor side plate RH | black/part of E2D/1935 | ||
192 |
Motor support bracket | unknown finish/1930(?)-35(?) | ||
494 |
Wrench/single ended | nickelplated/Erector MW/1933-35 | ||